How Do You Explain Replace A Window To A Five-Year-Old > 자유게시판

How to Replace a Window

When replacing a window it is essential to ensure that the new window is square and accurate. Measure the width of the frame at the bottom and in the middle, and at the top. When measuring make sure you highlight or circle the smaller number.

Use a screw that is loose through one of the side jambs on the upper portion to ensure that your window is sized correctly. Remove the sash cords, pulleys, and weights.

Installation

Work from the inside to put in the glass window replacements from the inside. The first step is to secure it to the opening with 2 inches of screws driven through one of the upper side jamb holes and this is all you require to hold the window in place while you test its fit and shim it, should you need to. Once the window is set and you have it in place, take a diagonal measurement on both sides of frame to ensure that it is square and aligned. Use a level to make sure that the top and bottom corners are plumb; if not, put wood shims underneath the frame at every corner.

If you've got a lot of caulk and paint in the opening, use a or hammer to get rid of it. This will result in an even clean and clear surface. Vacuum the frame and sills to remove dirt, dust and debris. Remove any staples that are securing the frame from the brick molding or wall where the old frame used to be.

Apply an elastomeric sealant on the exterior of the frame in preparation for sealing. Use a caulking gun capable of giving a precise and even bead. Alternately, you can make use of a low-expansion foam sealant. A high-yielding canister is cheaper than a straw that can disperse a tube of foam.

Then, take off the sill stops, and glass Replace window the casing on the outside or brick mold that is located around the frame's bottom; this is usually only used on older homes. You can also reinstall the blind stops on the sides and top of the frame, but do it with care; they should be left loose until you attach them to the new window.

Pull the lower sash out of the window and cut the sash cords. Pull or remove the parting stop, (the strip that connects the upper and the lower sashes) and replace it with an internal wood stop. Make sure that the weatherstripping faces the outside. Attach the stop to the jambs of the frame, and the top using three finish nails for each stop.

When you're ready to reinstall the upper sash, insert it into place in the window and then slide the stool back up over it. Then, move the sash up and down and test the operation of the latches at the bottom to make sure that it slides easily. If necessary, install the weight pockets in the sash and then make sure that the pocket holes are filled with expanding foam. When you are sure that the window is installed correctly, drive a partial nail into the trim on one of the corners that is higher. Utilize a level to verify the window's plumb. If it's not, place shims to the frame at each of the four corners.

Measurement

If you're replacing a single window or your entire home there are some crucial steps to take to ensure that the new windows will fit properly and will provide the best energy efficiency. The first step is to determine the current windows' openings. This can be accomplished using a tape measure and a pencil. Begin by clearing away any clutter that might hinder the measurement, like curtains or blinds.

The width is the distance between the side jambs and the head jamb (the vertical board along which a window sash slides when it is opened and closed). The width is measured from the side jambs upwards to the headjamb (the vertical board that slides down when the window sash opens and closes). To determine the width, place your tape measure against the inside of the frame, in the bottom, middle and top areas. Mark the smallest measurement, which will be your rough window opening width.

The height is the distance between the head jamb to the sill, which is the horizontal trim board that extends out into the room. To determine the height, take three measurements of the sill on each side from the left, from the middle and from the right. The shortest of these measurements will be your window's opening height.

The depth is not as crucial, but it can still be a problem in certain situations. You'll need to remove the current interior trim and siding from the window frame to determine the exact depth. If you're using replacement windows that will be anchored to the sill, you'll need subtract two inches from this amount to ensure that the window will fit within the opening.

It's not difficult to measure for a replacement glass windows, but it is essential to make sure that your measurements are precise. You will also need to be aware of any particular installation requirements for the type you're putting in and whether it requires a nailing fin or is meant to be a replacement glass in windows for the brick opening.

Once you've got the measurements for your new window, you must verify that the frame is level, Glass Replace Window plumb and square. The standard sizes for replacement windows differ, so you need to ensure that all corners are on a 90-degree arc. To do this, hold your tape measure in the upper corner of the head jamb and extend it diagonally until the lower left-hand corner, where the horizontal and vertical trim boards meet. If the measurements are within quarter-inch of each other, your window will be square and plumb. If not, you'll have to shim the frame prior to installing the new window. It is important to speak with a professional if this is the case. They can help you decide the best window design and size for your specific home's situation.

Preparation

Installing new windows in your home will increase its energy efficiency, increase the value of your home and also make it more beautiful. It also helps to reduce maintenance over the long term and make your home more attractive to potential buyers. However, you need to do some preparation to make the installation process smooth. It is essential to ensure that the area around the window is clean to allow the workers to install it easily. In order to do this, remove all curtains and blinds that hang in the window. Take down any wall hangings that are near to the window and could be damaged during installation.

Your installers will need to measure the dimensions of your old window frame to get a precise fit for the new one. Measure the inside width of the frame from jamb to jamb in three locations at the top, middle, and bottom. Then, write down the lowest measurement. This will ensure that the new window will fit perfectly into the opening.

Once the measurements are taken, the installation team can begin the work. The process is much more complex than installing an insert glass replacement on windows because the installers must strip the entire window opening down to its framing rough, both outside and inside. This is the only choice for sills, frames and jambs have rotted.

The installers will make use of a blow torch in order to heat the caulking around the exterior of the window and then carefully cut away the frame made of wood. They will then use a circular saw to cut the siding from around the windows, to about 1 inch below the frame. This will allow the space needed for casing that will be affixed to the windows on all four sides and shield them from moisture damage.

The shims are placed on the inside of the window opening and the sill frame is built using a doubled 2x4. The shims are secured using silicone or two nail heads of 6d per shim. This will prevent the window from sliding over time. Installers will then finish off the opening by installing lower wall studs as well as a header and an exterior stop molding to match the rest of the house.

You can prevent a mess during installation by covering your flooring and furniture with drop cloths and plastic sheets. Also, cover any plants or trees with a tent or sheet to avoid any possible damage or trampling. It's recommended to take down any outdoor décor that could hinder the process as the crew works. The installation crew will try their best to avoid getting their feet on these objects. However, they might not be able to without your assistance.